80pctlower
Lowers that are nearly complete.
80% Lower receivers
80% lower receivers No FFL required, these are not lower receivers but are mearly incomplete until the following are completed.

Made of 7075 T6 forged Aluminium, same as normal completed lower receivers.

Pulled from final completion for sale as 80% percent AR-15 lower receiver (non finished).  These are made the same as normal lower receivers but require finishing to be classified as a firearm.

We also carry Jig Sets for the AR-15 and AR-10 Type lower receivers along with Lower receiver parts kits, stripped ar15 lower receivers, and complete ar15 lower receivers.

 

ARE These LEGAL? The answer is YES.  Here is the text info, and link to

the ATF website Page 177

(A6) Does the GCA (Gun Control Act ) prohibit anyone from making a handgun, shotgun or rifle? With certain exceptions a firearm may be made by a nonlicensee provided it is not for sale and the maker is not prohibited from possessing firearms. However, a person is prohibited from assembling a nonsporting semi-automatic rifle or nonsporting shotgun from imported parts. In addition, the making of an NFA firearm requires a tax payment and approval by ATF. An application to make a machinegun will not be approved unless documentation is submitted showing that the firearm is being made for a Federal or State agency.
[18 U.S.C. 922(o) and (r), 26 U.S.C. 5822, 27 CFR 478.39, 479.62 and 479.105]

We Do NOT use import parts so you can make your own AR-15 type lower receiver

!

80% lower receiver
!
80% lower receiver for AR-15 type rifles.

80% lower receiver.

Lower receivers that are nearly complete and only require

1.  Milling out of the receiver interior

2.  Cutting of the trigger slot

3.  Drilling of the trigger pin hole

4.  Drilling of the hammer pin hole.

5.  Drilling of the selector hole.

Completed areas:  Buffer tube area complete and threaded, detent pin holes drilled for both front pivot pin and rear takedown pin.  Magwell completely finished.  Pistol grip area finished with selector detent pin hole drilled, and threaded pistol grip screw hole.  Mag Catch and bolt catch area finished.  Trigger guard holes finished.

threaded buffer tubefinished pistol grip mount

left side viewlower receiver top view

ar15 right sidear15 take down pin and mag release button

 

.308 7.62 X 51 AR-10 80% complete Lower Receiver but is DPMS compatible.
!
308ltsidefull80pct
.308 left side full view. 

.308 7.62 X 51 AR-10 type 80 % lower receiver.  These are made for the DPMS Compatible style AR-10.  This 80% lower also uses the same lower Receiver fire control kit as the AR-15 and are found HERE.

NOW MADE FROM 7075 T6 Aluminum Billet.

80% AR-10 lower receiver.

Lower receivers that are nearly complete and only require

1.  Milling out of the receiver interior

2.  Cutting of the trigger slot

3.  Drilling of the trigger pin hole

4.  Drilling of the hammer pin hole.

5   Drilling of the selector hole.

*****Due to a New Determination by ATF The selector hole will not be drilled ***

Completed areas:  Buffer tube area complete and threaded, detent pin holes drilled for both front pivot pin and rear takedown pin.  Magwell completely finished.  Pistol grip area finished with selector detent pin hole drilled, and threaded pistol grip screw hole.  Mag Catch and bolt catch area finished.  Selector markings.  Trigger guard holes finished.  Everything that is finished is to specification.   

** includes 2 set screws and pins for bolt catch pivot and rear takedown pin detent.

 AR-10 threaded buffer tube areaAR-10 lower receiver pistol grip

AR-10 trigger areaAR10 bolt catch

AR10 top viewAR10 mag catch

AR10 mag wellmagazine catch

AR-10 bolt catch

 Lower Parts kits for this 80% AR-10 lower Here